Classification:

Reference:

EL25-011

Date:

NTB25-046

October 14, 2025

VOLUNTARY SERVICE CAMPAIGN
2025 ROGUE; REMOTE ENGINE START BCM CONFIGURATION
CAMPAIGN ID #:
APPLIED VEHICLES:

PD175
2025 Rogue (T33)

Check Service COMM or Dealer Business Systems (DBS)
National Service History to confirm campaign eligibility.

INTRODUCTION
Nissan is conducting this voluntary service campaign on certain specific model year 2025
Rogue vehicles to reconfigure the BCM. This service will be performed at no charge to the
customer for parts or labor.

IDENTIFICATION NUMBER
Nissan has assigned identification number PD175 to this campaign. This number must
appear on all communication and documentation of any nature dealing with this campaign.

DEALER RESPONSIBILITY
Dealers are to repair vehicles falling within range of this campaign that enter the service
department. This includes vehicles purchased from private parties, vehicles presented by
transient (tourists) owners, and vehicles in a dealer’s inventory.

Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.
1/13

SERVICE PROCEDURE
BCM Configuration
HINT: If the Wi-Fi connection is not sufficient or is unstable, data may not download
correctly during this procedure.
IMPORTANT: Before beginning the following procedure, verify the following:

1.

•

ASIST on the CONSULT PC has been synchronized (updated) to the current date.

•

All CONSULT 4 software updates (if any) have been installed.

•

The CONSULT PC is connected to the internet via a cable or Wi-Fi.

•

Later in the procedure you will be required to enter your username and password.

•

If you do not know your username and password, contact your service manager.

•

No diagnostic trouble codes (DTCs) are stored.

Connect the Vehicle Interface (VI3) to the vehicle Data Link Connector (DLC).
•

Connect the provided USB cable to the VI3 and the CONSULT PC.

Make sure the VI3 is securely connected. If the VI3 connection is loose during
reprogramming, the process will be interrupted and the control unit may be damaged.

VI3

Figure 1

2/13

NTB25-046

2.

Connect the AC Adapter to the CONSULT PC.

Be sure to connect the AC Adapter. If the CONSULT PC battery voltage drops during
reprogramming, the process will be interrupted and the control unit may be damaged.
3.

Open the hood.

4.

Connect a battery maintainer or smart charger set to reflash mode or a similar setting.
To avoid damage to the control unit, ensure a battery maintainer or smart charger is
connected. The battery voltage must be between 12.0V and 13.5V during
reprogramming.

5.

Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.) within range
of the CONSULT PC and the VI3.
If Bluetooth® signal waves are within range of the CONSULT PC and the VI3 during
reprogramming, reprogramming may be interrupted, and the control unit may be
damaged.

6.

Turn the ignition ON (engine OFF) by pressing the push button ignition switch one
time without depressing the brake pedal (Figure 2).
To avoid damage to the control unit, the engine must not start or run during the
reprogramming procedure.

Push button
ignition
switch

Figure 2

3/13

NTB25-046

7.

Turn OFF all vehicle electrical loads such as exterior lights, interior lights, HVAC,
blower, rear defogger, audio, NAVI, seat heater, steering wheel heater, etc.

8.

Turn ON the hazard warning lamps.

9.

Start the CONSULT 4 (C4) program
by selecting the C4 icon on the
desktop or taskbar (Figure 3).

Figure 3
10.

Enter login information and select Submit (Figure 4).
•

If prompted, select USA/CANADA Dealers from the drop-down menu, and then
select OK.

IMPORTANT: If not prompted to enter your username and password, the CONSULT
PC may not be connected to Wi-Fi. Close CONSULT 4, confirm the CONSULT PC is
connected to Wi-Fi, and then reopen CONSULT 4.

Figure 4

4/13

NTB25-046

11.

Allow C4 to connect to the VI3 (Figure 5).
HINT: VI3 may not automatically connect the first time logging in. If the VI does not
automatically connect, select Change VI on the RH side of the screen.

Change
VI
Figure 5

12.

Allow system call to perform (Figure 6).
xxxxxx

xxxxxxxxxxxxxxxx

Figure 6

5/13

NTB25-046

13.

Locate and select Vehicle reprogramming (Figure 7).
xxxxx

xxxxxxxxxxxxxxxx

Figure 7

14.

Allow C4 to check for reprograms (Figure 8).
•

This process may take several minutes.
xxxxx

xxxxxxxxxxxxxxxx

Figure 8

6/13

NTB25-046

15.

If the screen shown in Figure 9 is displayed, continue to step 16. If the screen shown
in Figure 9 is NOT displayed, skip to step 17 on page 9.

xxxxxxxxxxxxxxxx

Figure 9

16.

Select Yes without entering anything into the text box (Figure 10).

xxxxxxxxxxxxxxxx

Leave this text box empty

Figure 10

7/13

NTB25-046

•

When the screen shown in Figure 11 is displayed, select Yes.

xxxxxxxxxxxxxxxx

Figure 11
•

The screen will be blank for approximately 1 minute (Figure 12).

•

Continue to step 17 on page 9.

Figure 12

8/13

NTB25-046

17.

Scroll down to locate BCM.
•

Select the “X” at the bottom RH corner, as shown in Figure 13.

•

Select the “Play” icon for BCM, as shown in Figure 13.

HINT: CFG in the second column indicates “configuration”

CFG =
Configuration
Play icon

Figure 13

18.

Verify the 12 volt battery is between 12.0V and 13.5V and select Next (Figure 14).

Figure 14

9/13

NTB25-046

19.

Allow the configuration to complete (Figure 15).
•

This process will take 2-3 minutes.

Figure 15

20.

Once the screen shown in Figure 16 is displayed, select Complete.

Figure 16

10/13

NTB25-046

21.

Select All self diagnosis result and confirm if any DTCs are present (Figure 17).

Figure 17

22.

If any past DTCs are present, erase all the DTCs as follows:
•

Select the “Erase DTC” icon, and select Yes to erase (Figure 18).
Erase DTC

Figure 18

11/13

NTB25-046

23.

Verify all DTCs have erased (Figure 19).

Figure 19
24.

Close C4 by selecting the “X” in the upper RH corner (Figure 20).

Figure 20
25.

Turn the ignition OFF by pressing the push button ignition switch one time without
depressing the brake pedal.

26.

Disconnect the VI3 from the vehicle.

27.

Disconnect the battery maintainer or smart charger from the vehicle.

28.

Close the hood.

12/13

NTB25-046

CLAIMS INFORMATION
Submit a “CM” line claim using the following claims coding:
CAMPAIGN (“CM”) ID

DESCRIPTION

OP CODE

FRT

PD175

Reconfigure BCM

PD1750

0.4

AMENDMENT HISTORY
PUBLISHED DATE REFERENCE
October 14, 2025

NTB25-046

DESCRIPTION
Original bulletin published

13/13

NTB25-046