ZN Connection offline

Technical Service Bulletin Transaction No.: 2079692/3
00 Aid for TSB 2079690 (00 Combined software update 03.10.00/C (28.13.01) KD2)) Release date: Jan 22, 2026

Condition

Model(s) Year(s) VIN Range Vehicle Specific Equipment

Ad, S5 (FU), A6 Sportback
e-tron, S6 Sportback e-
tron, Q5, Q5 Sportback,

SQ5, SQ5 Sportback
(GU), Q6 e-tron, Q6
Sportback e-tron, SQ6 e-
tron, and SQ6 Sportback
e-tron

2025 All Not applicable

REVISION HISTORY

Revision | Date Purpose

3 - Revised Service (Updated verbiage)

2 10/25/2025 | Revised header (Add PPC - Q5/A5)

1 10/10/2025 | Initial publication

Aid document if flashing is aborted for TSB 2079690, 00 Combined software update 03.10.00/C (28.13.01) KD2.

Technical Background
Not applicable.

Production Solution
Not applicable.

Service

General information:

If a vehicle has already been updated partially using a code and an error occurred during the update, do not attempt
to repair the vehicle via "SVM - Check vehicle configuration”.

Please make absolutely sure to observe the information displayed on the tester before sending a support request.

1) Displayed on ODIS tester:
0x0009 Control module in after-run
Complaint:

Programming conditions not met
Solution:

Erase event memory and perform update again without switching ignition off and on again.

2) Complaint after update:

None

Complaint:

Rear lid closes without power latching system after a successful update.
Solution:

Please note the information in TSB 2080580, 55 Rear lid does not close properly after software update.

3) Displayed on ODIS tester:

8118 and possibly fault message SDB20FOE (control module cannot be reached) (diagnostic addresses 00C5 and
8132)

Complaint:
Flashing aborted for onboard supply control unit (DAQOC5)
Solution:

Replace onboard supply control unit, commission control unit, perform software update

4) Displayed on ODIS tester
8118 Diagnostic addresses (062A and 062B)
Solution:

Please note the information in TSB 2080352, 69 PSS Reversible belt tensioners cannot be reached identified in
event memory SVM error code 8118.

5) Displayed on ODIS tester:
8024
Solution:

An incorrect SVM code was entered. Please note that multiple SVM codes are available (distinction between PPE
and PPC).

6) Complaint after update

Displayed on ODIS tester:

Not applicable.

Complaint:

Message in instrument cluster: Adaptive cruise assist currently unavailable
Solution:

After the update, all vehicle doors and the rear lid must be opened and closed once.

7) Displayed on ODIS tester:
8118 and possibly fault message SDB20F0E (control module cannot be reached)
Diagnostic address(es) with general error. (It may not be possible to reach the diagnostic addresses listed in the
vehicle. Check communication with diagnostic address and, if necessary, switch ignition off and on again or wait for
a bus sleep cycle):

DA -— control unit name
Complaint:

One or more control units log on incorrectly or cannot be reached (only applies when SVM code is entered for the
first time).

Solution:

Please attempt to restore communication capability via GFF. If this is not successful, please open a ticket with the
Technical Assistance Center (TAC) (IMPORTANT: code on affected control unit).

8) Displayed on ODIS tester:
The following event has occurred:
8060 or

8096

Complaint:

Possible causes: lost configuration after a software update or control units which can no longer be reached due to a
software update.

Solution:
Perform bus sleep cycle (at least 15 minutes) and then repeat procedure using SVM code.

9) Displayed on ODIS tester:

9024 or ODS1008E

Connection

Negative response from server

Complaint:

When the GSB bus times out, the ODIS-S tester makes four attempts to establish the connection.
Solution:

Perform update again. If this is unsuccessful, please contact TAC.

10) Complaint after update
Displayed on ODIS tester:
N/A

Complaint:

Vibration of the steering wheel during the flashing procedure is a normal occurrence. If the steering wheel still
vibrates after the update has been completed, please refer to the TSB specified below.

Solution:

Refer to TSB 2076547, 48 General information on flashing procedure (vibrating steering wheel).

11) Displayed on ODIS tester:
File transmission freezes for longer than 5 minutes. ODIS tester displays message about this for longer than 5
minutes.

Complaint:

The data required for the software update cannot be downloaded from the workshop server (EdgeBox). This is
generally caused by a firewall setting on the workshop tester.

If this error occurs for the first time, please check the firewall settings (refer to campaign description) and enter the
code again.

Solution:

Please check the EdgeBox and firewall settings with the help of your IT administrator and configure the firewall in
accordance with the ODIS release notes. In particular, it is necessary to enable port 8080.

12)Displayed on ODIS tester:

Error codes:

8060, 8118, 8125, 8090, SDB20FOE (control module cannot be reached) (diagnostic addresses 8117 and 006C)
Complaint:

Flashing aborted at diagnostic address O06C; diagnostic address 8117 can no longer be reached

Solution:

Please note the information in TSB 2080613, 00 Workshop info: irregularities when performing KD2 combined
software update on diagnostic address 8117+006C - PPE/PPC.

13)Displayed on ODIS tester:

8060 or 8118 (possible diagnostic address: 4200, 4201, 4202, 4203)

Complaint:

Multiple electric exterior door handles can no longer be reached after flashing is aborted.

Solution:

Please note the information in TSB 2080648, 57 One or more electric exterior door handles cannot be reached
during KD2 update.

Warranty

This TSB is informational only and not applicable to any Audi Warranty.

Additional Information

All part and service references provided in this TSB (2079692) are subject to change and/or removal. Always check
with your Parts Department and/or ETKA for the latest information and parts bulletins. Please check the Repair
Manual for fasteners, bolts, nuts, and screws that require replacement during the repair.

©2026 Audi of America, Inc. All rights reserved. The information contained in this document is based on the latest
information available at the time of printing and is subject to the copyright and other intellectual property rights of
Audi of America, Inc., its affiliated companies, and its licensors. All rights are reserved to make changes at any time
without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form
or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be
modified or reposted to other sites, without the prior expressed written permission of the publisher.