NHTSA ID Number: 11719477
Complaint Date: 2026-02-20
Fail Date: 2025-01-09
Manufacturer Name: Ford Motor Company
Vehicle Make: FORD
Vehicle Model: MAVERICK
Model Year: 2023
Summary
Hybrid Ford Maverick electrical system began to go into a save battery mode -no interior lights, only driver side door operated, and other system failures. Dealer replaced battery under warranty and general recall for this issue. A few months later same characteristics started showing up -interior lights not working, only driver's side door operational, etc. This time the warranty had expired and the dealer, along with Ford Motor, told me any repairs would be at my expense, 100%. I feel problem was never resolved, even with replacement battery. Ford and dealer should address this problem. I'm sure I'm not the only one with this battery and electrical issue. After all, there was a full recall for the battery failure. Having no interior lights, unable to enter except driver's side, and other manifestations are inherently unsafe.
Read More...NHTSA ID Number: 11719476
Complaint Date: 2026-02-20
Fail Date: 2025-12-15
Manufacturer Name: General Motors, LLC
Vehicle Make: CHEVROLET
Vehicle Model: SILVERADO 1500
Model Year: 2021
Summary
The vehicle involved is a Chevrolet Silverado 1500. During a collision, the vehicle sustained a front-left (driver-side) impact which caused it to spin and subsequently strike the rear. Despite the severity of the initial impact and secondary rear collision, the Supplemental Restraint System (SRS), including the front and side airbags, did not deploy. The failure of the airbag system increased the risk of injury to all occupants, including a minor child. Without deployment of the front or side airbags during a front-left impact and secondary rear collision, occupants were exposed to direct impact forces that airbags are designed to help mitigate. There were no airbag or SRS warning lights, dashboard messages, or other indications of a malfunction prior to the collision. The concern regarding the airbag system arose only after the incident occurred. Following the collision, the vehicle was inspected by law enforcement and insurance representatives, and documentation is available. The issue has not been reproduced, as it occurred during the collision event.
Read More...NHTSA ID Number: 11719475
Complaint Date: 2026-02-20
Fail Date: 2025-09-01
Manufacturer Name: Volkswagen Group of America, Inc.
Vehicle Make: VOLKSWAGEN
Vehicle Model: TIGUAN
Model Year: 2022
Summary
Vehicle started smoking last September/October (2025) after catching several examples of it on camera, VW says it needs new heads. I’ve been on a “waiting list” ever since. The vehicle continues to get worse, recently the low oil light came on as it burns oil excessively . I’ve called VW and they’ve documented it. I’m concerned because I work out of town - My wife drives this car with our 2 1/2 year old and 5 month old.
Read More...NHTSA ID Number: 11719474
Complaint Date: 2026-02-20
Fail Date: 2026-02-14
Manufacturer Name: Nissan North America, Inc.
Vehicle Make: NISSAN
Vehicle Model: ROGUE
Model Year: 2014
Summary
My husband and I were in a head on and sustained injuries to my neck, chest abdomen, and knees. Neither the driver nor the passenger airbags went off during the accident. No lights were present no warning, lights or messages prior to the accident and we were both wearing our seatbelts. I received significant whiplash, bruising, and injuries confirmed by x-rays and feel that the airbags not going off in this collision only made it worse.
Read More...NHTSA ID Number: 11719473
Complaint Date: 2026-02-20
Fail Date: 2026-02-06
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: JEEP
Vehicle Model: CHEROKEE
Model Year: 2019
Summary
The contact owns a 2019 Jeep Cherokee. The contact stated that while driving at an undisclosed speed, the message "Service 4WD" was displayed on the instrument panel. The vehicle was taken to Firestone, where it was diagnosed, and DTC: C14A7-97 was retrieved. The contact was informed that the code indicated that the transfer case range position sensor was obstructed or blocked. The contact was informed that the failure was due to the Power Transfer Unit (PTU). The second diagnostic code was U0010-00, which involved the Instrumental Panel Cluster (IPC) and the Controller Area Network (CAN) interior box. The third code was U0140, which involved the "Lost Communication with Body Control Module (BCM)”. The vehicle was not repaired. The vehicle was then taken to a transmission specialty shop, where the DTC codes were confirmed. The vehicle was not repaired. The vehicle was then taken to the dealer, where the diagnostic codes were confirmed. The vehicle remained at the dealer unrepaired. The manufacturer was not made aware of the failure. The approximate failure mileage was 121,000.
Read More...NHTSA ID Number: 11719472
Complaint Date: 2026-02-20
Fail Date: 2025-12-04
Manufacturer Name: Ford Motor Company
Vehicle Make: FORD
Vehicle Model: EDGE
Model Year: 2021
Summary
My vehicle was recalled by the manufacturer for possibly defective intake valves. The manufacturer did a destructive test on the valves, This test consisted of running the car at 4500 rpm (approximately 120 mph) for a period of approximately 50 minutes. Since this test my car has undergone 3 transmission repairs. Any of these conditions could have resulted in being stranded on the road or possibly losing control of the vehicle, The test only makes the assumption that if the valves did not fail during the test they will continue to provide adequate and safe service. This is not necessarily true. The valves may fail on the highway causing loss of control, I believe that my vehicle was damaged by this test. My vehicle has a little over 30, 000 miles and had no damage before this test. The manufacturer should make this good on the intake valves by replacing them on the 90,000+ vehicles subject to this recall.
Read More...NHTSA ID Number: 11719471
Complaint Date: 2026-02-20
Fail Date: 2025-01-05
Manufacturer Name: Subaru of America, Inc.
Vehicle Make: SUBARU
Vehicle Model: FORESTER
Model Year: 2020
Summary
The airbag system has a sensor issue and I keep getting warnings from Subaru to get it fixed because it affects the seatbelts. The garage where I take my car says they are unable to get the part needed for the passenger sensor. And, Subaru says they need to replace the whole harness for $6000. Makes me wonder why a safety issue like this one seen in other Subaru’s have been recalled but not my model… Also the start stop feature drains the battery excessively. I have had to replace the battery twice in less than a year. I push the button to stop this feature the minute I get into the car.
Read More...NHTSA ID Number: 11719470
Complaint Date: 2026-02-20
Fail Date: 2026-02-20
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: RAM
Vehicle Model: 1500
Model Year: 2016
Summary
My truck lost power steering while driving, a red flashing light came on saying power steering, pulled off and could not turn wheel. Managed to get it to a shop close by and upon scan for codes it came up C2217-00 electric power steering and shop verified that my truck came up with a recall regarding this same issue but when I called a dodge dealership they said I had no open recalls yet needed to get it to their shop for their diagnostic.
Read More...NHTSA ID Number: 11719469
Complaint Date: 2026-02-20
Fail Date: 2024-02-20
Manufacturer Name: Kia America, Inc.
Vehicle Make: KIA
Vehicle Model: SOUL
Model Year: 2021
Summary
The contact owns a 2021 Kia Soul. The contact stated that while driving at an undisclosed speed, the check engine warning light illuminated, and the engine seized. The contact stated that nearby drivers assisted with pushing the vehicle to the shoulder of the roadway. The failure had occurred while driving on a busy highway. While attempting to restart the vehicle, the vehicle started; however, it was unsafe to drive the vehicle. The vehicle was towed to the dealer, where it was diagnosed with engine failure. The contact was informed that the engine needed to be replaced. The vehicle was not repaired. Prior to the engine seizing, the vehicle was consuming an excessive amount of engine oil. The contact stated that 3 to 4 quarts of oil needed to be added between oil changes. In addition, the contact stated that in 2021, the vehicle was repaired under NHTSA Campaign Number: 21V259000 (Engine). The contact stated that after the recall repair was performed, the excessive oil consumption started. The manufacturer was not made aware of the failure. The failure mileage was approximately 88,200.
Read More...NHTSA ID Number: 11719468
Complaint Date: 2026-02-20
Fail Date: 2026-02-18
Manufacturer Name: Nissan North America, Inc.
Vehicle Make: NISSAN
Vehicle Model: PATHFINDER
Model Year: 2025
Summary
While driving at highway speeds, my 2025 Nissan Pathfinder suddenly loses power and enters limp mode with no warning. The dashboard displays: “Engine Malfunction – Power Reduced – Service Now.” When this happens, the vehicle cannot accelerate and struggles to maintain speed, creating a serious safety hazard in traffic. This has occurred multiple times. First time was on January 6th - entered highway and car stalled, was able to pull over and have the car towed to the dealer and they stated, "cannot replicate the issue". Second time February 15th - car stalled on highway and Husband was able to pull over and restart the car. Third time was February 18th - car entered limp mode on the highway, car was towed to the dealer and they have yet again stated, "cannot replicate the issue". During each event, the Pathfinder rapidly decelerates, and I am forced to pull over immediately to avoid being hit from behind. The loss of propulsion happens suddenly and without any driver input. This places me and other drivers in danger, especially at high speeds and on icy Alaska roads. Two of the times was during snowstorms with low visibility. Attempts to Repair: I have taken the vehicle to the Nissan dealership. The dealer states they “cannot replicate the issue” and returns the vehicle without repair. However, the warning message and limp-mode event clearly indicate an engine or powertrain failure. The issue continues to reoccur despite these visits. Safety Concern: Because the vehicle loses power in fast-moving traffic and enters limp mode, it poses a substantial risk of collision or injury. This defect could cause a serious accident, especially at highway speeds or in winter driving conditions.
Read More...
- CEL Doctor: The ANCEL AD310 is one of the best-selling OBD II scanners on the market and is recommended by Scotty Kilmer, a YouTuber and auto mechanic. It can easily determine the cause of the check engine light coming on. After repairing the vehicle's problems, it can quickly read and clear diagnostic trouble codes of emission system, read live data & hard memory data, view freeze frame, I/M monitor readiness and collect vehicle information.
- Sturdy and Compact: Equipped with a 2.5 foot cable made of very thick, flexible insulation. It is important to have a sturdy scanner as it can easily fall to the ground when working in a car. The AD310 OBD2 scanner is a well-constructed mechanic tool with a sleek design. It weighs 12 ounces and measures 8.9 x 6.9 x 1.4 inches. Thanks to its compact design and light weight, transporting the device is not a problem. The buttons are clearly labelled and the screen is large and displays results clearly.
- Accurate Fast and Easy to Use: The AD310 scanner can help you or your mechanic understand if your car is in good condition, provides exceptionally accurate and fast results, reads and clears engine trouble emission codes in seconds after you fixed the problem. This device will let you know immediately and fix the problem right away without any car knowledge. No need for batteries or a charger, get power directly from the OBDII Data Link Connector in your vehicle.
- OBDII Protocols and Car Compatibility: Many cheap scan tools do not really support all OBD2 protocols. AD310 scanner as it can support all OBDII protocols such as KWP2000, J1850 VPW, ISO9141, J1850 PWM and CAN. This device also has extensive vehicle compatibility with 1996 US-based, 2000 EU-based and Asian cars, light trucks, SUVs, as well as newer OBD2 and CAN vehicles both domestic and foreign. Pls confirm with our customer service whether it is compatible with your vehicle before purchasing.
- Home Necessity and Worthy to Own: This is an excellent code reader to travel or home with as it weighs less and it is compact in design. You can easily slide it in your backpack as you head to the garage, or put it on the dashboard, this will be a great fit for you. The AD310 is not only portable, but also accurate and fast in performance. Moreover, it covers various car brands and is suitable for people who just need a code reader to check their car.
- Multi-Functions - Practical Multi-Functions OBD2 code reader features built-in OBD2 DTC lookup library, which help you to determine the cause of the engine light, read code, erase code, view freeze frame, I/M ready, vehicle information, data flow, real-time curve, get vehicle speed information, calculate load value, engine coolant temperature, get engine speed.
- Wide Capability - Supports 9 protocols compatible with most 1996 US-Based, 2000 EU-Based and Asian cars, and newer OBD II & CAN domestic or import vehicles. Supports 6 languages - English,German, Dutch, Spanish, French, Italian.
- 2.8" LCD Display - Designed with a clear display 2.8" Large LCD screen - white backlight and contrast adjustment. No need any battery or charger, OBD reader gets the power directly from your vehicle through the OBDII Data Link Connector.
- Compact Design - Car diagnostic scanner is equipped with a 2.5 feet long cable and made of a very thick flexible insulator.There are 6 buttons on OBD2 Scanner:scroll up/down,enter/exit and buttons that quick query VIN vehicle number& the DTC fault code.
- ABS / Airbag codes NOT Supported - It is able to read and clear check engine information which is part of OBDII system, but it cannot work with non-OBDII systems, including ABS / Airbag / Oil Service Light, etc.
- 【Your Personal CEL Doctor – Read & Clear Engine Codes】The NT301 OBD2 scanner lets you read diagnostic trouble codes (DTCs), check em-issions readiness, turn off your Check Engine Light (CEL) or MIL, reset monitors, and view live data streams. It retrieves your vehicle's VIN instantly. Like all standard OBD2 scanners, it clears codes only after repairs are completed—if the issue persists, the code will return. Designed for DIYers who want to understand what’s really going on under the hood.
- 【Easy Code Reading – Just Plug & Play】Simply plug into the OBD2 port, turn the ignition to “ON” (engine off), and select the correct menu: Select OBDII-> Wait for seconds-> Select Read codes. For accurate results, ensure your vehicle is compatible and the OBD2 port is free from damage or wiring issues. No batteries needed— powered directly by your car.
- 【Live Data Graphing & Accuracy for Most OBD2 Vehicles】View and log live sensor data in graph form—monitor oxygen sensors, fuel trims, coolant temp, RPM, and more. Spot trends and suspicious values in real time. Compatible with most 1996+ gasoline cars, light trucks, and SUVs sold in the U.S., as well as many 2000+ European and Asian models. Also works on 12V diesel vehicles equipped with OBD2.
- 【S-mog Check Helper – Know Your Readiness Status at a Glance】With dedicated I/M readiness hotkeys and a simple Red-Yellow-Green LED indicator, you’ll instantly know if your vehicle is ready for em-issions testing. Built-in speaker provides audio feedback. No guesswork—just confidence before you head to the test center.
- 【A Must-Have Tool for Every Home Mechanic】Compact, rugged, and ready to use right out of the box. The 2.8” color screen is easy to read, even in daylight. No charging or setup required—just plug into the 16-pin DLC and start diagnosing. Recommended by professional mechanics on YouTube and trusted by DIYers worldwide.
Last update on 2026-03-26 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.