NHTSA ID Number: 11720317
Complaint Date: 2026-02-24
Fail Date: 2026-02-06
Manufacturer Name: Nissan North America, Inc.
Vehicle Make: NISSAN
Vehicle Model: ROGUE
Model Year: 2024
Summary
Check engine light came on. I hooked it up to a machine and read a code P2101 which indicates. Throttle actuator controlled motor store current failure. I had told to Nissan they did an inspection came back that he cleaned the throttlebody charge me $1053 and sent me on my way and my check engine light keeps coming on and it’s a recall on this particular car with this particular problem, but my VIN number is not showing up.
Read More...NHTSA ID Number: 11720316
Complaint Date: 2026-02-24
Fail Date: 2025-12-30
Manufacturer Name: Volkswagen Group of America, Inc.
Vehicle Make: AUDI
Vehicle Model: Q5
Model Year: 2025
Summary
The air bag keeps showing it's not working and that's it's turned off, there's a driving system malfunction, and warning lamp flashing emissions-related fault malfunction are not working. It is a brand-new car and after 2 months, all the malfunction lights keep showing so we went to the Audi dealership and they said they have ordered the parts from Germany, but it has almost been 2 months, and they still don't know when it will arrive.
Read More...NHTSA ID Number: 11720315
Complaint Date: 2026-02-24
Fail Date: 2026-02-24
Manufacturer Name: Honda (American Honda Motor Co.)
Vehicle Make: HONDA
Vehicle Model: PILOT
Model Year: 2024
Summary
The vehicle previously experienced a steering wheel locking issue and was taken to the dealer for repair. The dealer stated the issue was repaired on December 11, 2024. On February 24, 2026, while driving on a public street, the vehicle hesitated or jerked slightly during acceleration and then appeared to operate normally. After a few minutes, multiple warning messages suddenly appeared on the dashboard, and the steering wheel became extremely difficult to turn and effectively locked while I was driving. I immediately activated my hazard lights. I was unable to safely pull over because the steering wheel would not respond properly, which placed me and other drivers at risk. I had to continue driving slowly until I found a side road where I could safely stop. I turned the vehicle off. When restarting, the warning messages reappeared. After several minutes, the warning lights cleared, and the steering wheel was no longer locked but felt loose and unstable ("wobbly"). I cautiously resumed driving. After several minutes, the steering began to feel normal again. The following warnings were displayed: Hill Start Assist problem, Trailer Stability Assist problem, Hill Descent Control problem, Adaptive Cruise Control problem, Lane Keeping Assist problem, Collision Mitigation Braking System problem, Road Departure Mitigation problem, Low Speed Braking Control problem, Auto High-Beam problem, Electric Power Steering system problem – Steering Assist Not Available, and "Stop. Steering assist reduced. Stop driving when safe." The failed component appears to be the Electric Power Steering system and related driver-assistance systems. The vehicle is available for inspection. The problem was previously addressed by a dealer but has reoccurred. No prior warning lights were present before this incident. The failure occurred suddenly while driving.
Read More...NHTSA ID Number: 11720314
Complaint Date: 2026-02-24
Fail Date: 2025-05-01
Manufacturer Name: Honda (American Honda Motor Co.)
Vehicle Make: HONDA
Vehicle Model: ACCORD
Model Year: 2016
Summary
White paint peeling in rear rain gutter. Causing erosion.
Read More...NHTSA ID Number: 11720313
Complaint Date: 2026-02-24
Fail Date: 2026-02-17
Manufacturer Name: General Motors, LLC
Vehicle Make: CHEVROLET
Vehicle Model: SILVERADO 1500
Model Year: 2025
Summary
Driving 30 mph down a city street when heard a pop and vehicle completely lost power at speed. Engine turned off and I coasted to a stop, which was unfortunately at an intersection and due to traffic could not get over safely. All accessories were still on however I could not restart the vehicle or put the vehicle into neutral, which left me stranded in the middle of a busy intersection. Hazards were working intermittently, at best. Had to call local PD to provide traffic control while we disconnected the battery and reconnected it while standing in an intersection. After I was able to get the vehicle restarted it had a check engine light and the OnStar app showed Transmission, Ignition, and Engine Electrical warnings. Had the vehicle towed to the dealership, where they have had it for 7 days and cannot diagnose an issue and are trying to return the vehicle to me unfixed. They stated they typically would not even try to diagnose it for this long, however I have a case open with the GM executive team.
Read More...NHTSA ID Number: 11720312
Complaint Date: 2026-02-24
Fail Date: 2023-04-04
Manufacturer Name: Hyundai Motor America
Vehicle Make: HYUNDAI
Vehicle Model: TUCSON
Model Year: 2019
Summary
Catalytic converter and oil leak which is causing the vehicle to lose power. The catalytic converter was replaced in 2024 and now is bad again in 2025. Oil consumption has been a problem since 2024. Hyuandi is refusing to repair the vehicle. Despite the engine making a knocking noise and the check engine light is flashing the vehicle is still under the 150,000 power train warranty
Read More...NHTSA ID Number: 11720311
Complaint Date: 2026-02-24
Fail Date: 2026-02-22
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: JEEP
Vehicle Model: CHEROKEE
Model Year: 2019
Summary
I was driving on the highway and experienced what felt like a brief power outage where my vehicle instantly dropped speed. I estimate it was approximately 10-15 mph. Everything appeared to return to normal at the time until approximately 5 minutes later when I exited the highway and it began making a loud noise. I drove a couple miles before getting concerned and thinking I don't want to risk breaking down on the side of the highway going home or doing further damage to an expensive component such as engine or transmission. I used roadside assistance to tow my vehicle to my nearest dealership. The tow driver confirmed he heard the noise inside the vehicle while I stood outside and could not hear it. The dealership called me to approve the diagnostic fee and also asked questions about what happened. In hindsight, they had asked a very specific question regarding the noise sound and location which, in my opinion, shows they instantly suspected the issue that they would later report. After approving the fee, they sent a quote focused primarily around the rear differential housing being cracked for an estimate of $5221.85. I asked how this would happen and the service representative explained that the choke inside the differential broke and a piece of metal inside it cracked the housing. I began researching differentials in vehicles and specifically in Jeep Cherokees, I learned very quickly that this is a very common problem which explains how a representative was able to tell me the cause without seeing it. No warnings were ever issued on the dashboard and no symptoms were present prior to the sudden deceleration. There are no warnings on the dash after the event and the only symptom other than the noise while in motion is the acceleration/deceleration feels slightly less sensitive. Every potential cause stated by mechanics who have looked at this points to a manufacturing issue or quality issue. A complete failure could cause an accident harming people.
Read More...NHTSA ID Number: 11720310
Complaint Date: 2026-02-24
Fail Date: 2025-12-12
Manufacturer Name: Hyundai Motor America
Vehicle Make: HYUNDAI
Vehicle Model: ELANTRA
Model Year: 2017
Summary
I have been having this issue for several months. First, it was the steering wheel being locked. I believe at one point and time on the past they updated the computer on that vehicle. But this time the dealer told me there is nothing they can do. As of today, the car won’t start. How can I go to work? There is no Safety Recall for this, but I didn’t brake the car’s computer, I don’t even know and want to know where it is located.
Read More...NHTSA ID Number: 11720309
Complaint Date: 2026-02-24
Fail Date: 2026-02-24
Manufacturer Name: Nissan North America, Inc.
Vehicle Make: NISSAN
Vehicle Model: PATHFINDER
Model Year: 2025
Summary
I purchased this vehicle new, and it has exhibited multiple safety-related problems. 1.The transmission intermittently fails to engage reverse; when reverse is selected, the vehicle sometimes goes into neutral. 2.When this occurs, the rearview camera does not activate, creating a serious risk when backing up. 3.Additionally, the odometer/mileage appears to increase unusually fast without corresponding driving, suggesting a possible software malfunction affecting the vehicle’s electronic systems. These issues occur at low mileage, shortly after purchase. The combination of reverse failure and non-functioning rearview camera poses a direct safety hazard and may violate Federal Motor Vehicle Safety Standards (FMVSS) regarding rear visibility and transmission operation.
Read More...NHTSA ID Number: 11720308
Complaint Date: 2026-02-24
Fail Date: 2026-02-23
Manufacturer Name: Kia America, Inc.
Vehicle Make: KIA
Vehicle Model: NIRO
Model Year: 2025
Summary
I visited Car Pros Kia Tacoma for a wheel alignment on my 2025 Kia Niro EV. After the service, I was told the alignment was completed correctly and I was given a printout showing all values in the green. However, the vehicle did not feel stable or safe to drive afterward. The steering felt off, and the car did not track straight. Because the vehicle felt unsafe, I took it to Firestone the next day for a second opinion. Firestone performed a full alignment check and their “before” measurements showed that the alignment was significantly out of specification, including major issues with front toe, rear toe, and thrust angle. These values were far outside normal ranges and could affect handling and safety. Firestone then corrected the alignment, and their “after” measurements showed the vehicle was properly aligned and driving normally again. Their report clearly shows the difference between the unsafe alignment I received from Kia and the corrected alignment they performed. In summary: • Kia performed an alignment that was not actually within proper specifications. • I was told the alignment was correct when it was not. • The vehicle felt unsafe to drive after Kia’s service. • Firestone’s diagnostic confirmed the alignment was significantly off. • Firestone corrected the alignment and the vehicle immediately drove normally. I am filing this complaint because the dealership returned my vehicle in a condition that affected its stability and safety, and the documentation from Firestone clearly supports this.
Read More...
- CEL Doctor: The ANCEL AD310 is one of the best-selling OBD II scanners on the market and is recommended by Scotty Kilmer, a YouTuber and auto mechanic. It can easily determine the cause of the check engine light coming on. After repairing the vehicle's problems, it can quickly read and clear diagnostic trouble codes of emission system, read live data & hard memory data, view freeze frame, I/M monitor readiness and collect vehicle information.
- Sturdy and Compact: Equipped with a 2.5 foot cable made of very thick, flexible insulation. It is important to have a sturdy scanner as it can easily fall to the ground when working in a car. The AD310 OBD2 scanner is a well-constructed mechanic tool with a sleek design. It weighs 12 ounces and measures 8.9 x 6.9 x 1.4 inches. Thanks to its compact design and light weight, transporting the device is not a problem. The buttons are clearly labelled and the screen is large and displays results clearly.
- Accurate Fast and Easy to Use: The AD310 scanner can help you or your mechanic understand if your car is in good condition, provides exceptionally accurate and fast results, reads and clears engine trouble emission codes in seconds after you fixed the problem. This device will let you know immediately and fix the problem right away without any car knowledge. No need for batteries or a charger, get power directly from the OBDII Data Link Connector in your vehicle.
- OBDII Protocols and Car Compatibility: Many cheap scan tools do not really support all OBD2 protocols. AD310 scanner as it can support all OBDII protocols such as KWP2000, J1850 VPW, ISO9141, J1850 PWM and CAN. This device also has extensive vehicle compatibility with 1996 US-based, 2000 EU-based and Asian cars, light trucks, SUVs, as well as newer OBD2 and CAN vehicles both domestic and foreign. Pls confirm with our customer service whether it is compatible with your vehicle before purchasing.
- Home Necessity and Worthy to Own: This is an excellent code reader to travel or home with as it weighs less and it is compact in design. You can easily slide it in your backpack as you head to the garage, or put it on the dashboard, this will be a great fit for you. The AD310 is not only portable, but also accurate and fast in performance. Moreover, it covers various car brands and is suitable for people who just need a code reader to check their car.
- Multi-Functions - Practical Multi-Functions OBD2 code reader features built-in OBD2 DTC lookup library, which help you to determine the cause of the engine light, read code, erase code, view freeze frame, I/M ready, vehicle information, data flow, real-time curve, get vehicle speed information, calculate load value, engine coolant temperature, get engine speed.
- Wide Capability - Supports 9 protocols compatible with most 1996 US-Based, 2000 EU-Based and Asian cars, and newer OBD II & CAN domestic or import vehicles. Supports 6 languages - English,German, Dutch, Spanish, French, Italian.
- 2.8" LCD Display - Designed with a clear display 2.8" Large LCD screen - white backlight and contrast adjustment. No need any battery or charger, OBD reader gets the power directly from your vehicle through the OBDII Data Link Connector.
- Compact Design - Car diagnostic scanner is equipped with a 2.5 feet long cable and made of a very thick flexible insulator.There are 6 buttons on OBD2 Scanner:scroll up/down,enter/exit and buttons that quick query VIN vehicle number& the DTC fault code.
- ABS / Airbag codes NOT Supported - It is able to read and clear check engine information which is part of OBDII system, but it cannot work with non-OBDII systems, including ABS / Airbag / Oil Service Light, etc.
- 【Your Personal CEL Doctor – Read & Clear Engine Codes】The NT301 OBD2 scanner lets you read diagnostic trouble codes (DTCs), check em-issions readiness, turn off your Check Engine Light (CEL) or MIL, reset monitors, and view live data streams. It retrieves your vehicle's VIN instantly. Like all standard OBD2 scanners, it clears codes only after repairs are completed—if the issue persists, the code will return. Designed for DIYers who want to understand what’s really going on under the hood.
- 【Easy Code Reading – Just Plug & Play】Simply plug into the OBD2 port, turn the ignition to “ON” (engine off), and select the correct menu: Select OBDII-> Wait for seconds-> Select Read codes. For accurate results, ensure your vehicle is compatible and the OBD2 port is free from damage or wiring issues. No batteries needed— powered directly by your car.
- 【Live Data Graphing & Accuracy for Most OBD2 Vehicles】View and log live sensor data in graph form—monitor oxygen sensors, fuel trims, coolant temp, RPM, and more. Spot trends and suspicious values in real time. Compatible with most 1996+ gasoline cars, light trucks, and SUVs sold in the U.S., as well as many 2000+ European and Asian models. Also works on 12V diesel vehicles equipped with OBD2.
- 【S-mog Check Helper – Know Your Readiness Status at a Glance】With dedicated I/M readiness hotkeys and a simple Red-Yellow-Green LED indicator, you’ll instantly know if your vehicle is ready for em-issions testing. Built-in speaker provides audio feedback. No guesswork—just confidence before you head to the test center.
- 【A Must-Have Tool for Every Home Mechanic】Compact, rugged, and ready to use right out of the box. The 2.8” color screen is easy to read, even in daylight. No charging or setup required—just plug into the 16-pin DLC and start diagnosing. Recommended by professional mechanics on YouTube and trusted by DIYers worldwide.
Last update on 2026-03-23 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.