NHTSA ID Number: 11720657
Complaint Date: 2026-02-26
Fail Date: 2026-02-04
Manufacturer Name: General Motors, LLC
Vehicle Make: GMC
Vehicle Model: YUKON
Model Year: 2023
Summary
Vehicle developed hesitation. Message: "Reduced Acceleration Drive with Caution" Check Engine light comes on, fortunately near home. Scanner showed "PO 0747 Transmission Valve #1 stuck open." Research shows this is a common problem and a safety issue and can leave driver stranded or worse. Had vehicle "serviced" at selling dealer, but they did not touch the transmission. Said they drove it around the block and it was fine. Image attached. I was then told that parts are not available and GM will not authorize swapping out the valve body. Forums posts show a lot of dissatisfaction with GM over this issue.
Read More...NHTSA ID Number: 11720656
Complaint Date: 2026-02-26
Fail Date: 2026-02-12
Manufacturer Name: Subaru of America, Inc.
Vehicle Make: SUBARU
Vehicle Model: FORESTER
Model Year: 2017
Summary
The contact owns a 2017 Subaru Forester. The contact stated that upon opening the tailgate, the tailgate quickly fell unintendedly and struck the contact's head while the contact was retrieving items from the trunk. The contact sustained head soreness but had not received medical attention. The contact stated that the failure had occurred on several occasions. The vehicle was taken to the dealer, where it was diagnosed, and determined that the tailgate sending unit needed to be replaced. The vehicle was not repaired due to the cost. The failure mileage was approximately 85,000. The VIN was not available.
Read More...NHTSA ID Number: 11720655
Complaint Date: 2026-02-26
Fail Date: 2019-09-18
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: JEEP
Vehicle Model: WRANGLER
Model Year: 2019
Summary
Since new Jeep has experienced "excess play in the steering" the Jeeps steering "wanders" and vehicle pulls to both the left and right. Steering wandering increases in hot temperatures and at higher speeds and becomes UNSAFE to operate the vehicle. When purchasing new, I noticed the "excess play in the steering", but was told by the Jeep salesperson that "that's how Jeeps drive" and "They do not drive like typical passenger vehicles". I did not take my Jeep in for service for this issue because the salesperson told me that this is how the vehicle is designed to drive. However, I recently found out that Jeep issued a Technical Service Bulletin #08-074-20 REV.B back on September 26, 2020 that addresses this issue of "excess play in the steering" and "wandering" and the TSB gives recommendations to fix the steering by installing a new and improved Steering Gear Box that is made from steel as opposed to aluminum. I took my Jeep into a Jeep dealership with regards to this issue. The Jeep dealership confirmed that I have the "old style" steering gearbox mentioned in Technical Service Bulletin #08-074-20 REV.B and recommended that I replace it with the new design as recommended by the TSB. I asked Jeep to repair by vehicle free of charge as this is a "known" issue on Jeep Wrangler JL 2018-2020 as described in the TSB, but Jeep refused to pay for the safetly modification to my steering, stating that I am "out of the warranty period". This is a KNOWN manufacture defect. Jeep installed inferior aluminum steering gear boxes on their Jeep Wrangler JL 2018-2020 and 2020 Jeep Gladiators and they have since upgraded that critical safety component to a "steel version." Jeep should without question issue a "recall" to fix all current Jeep owners 2018-2020 Wrangler JLs and 2020 Jeep Gladiators that have a faulty aluminum steering gear box and replace it with the upgraded steel version that fixes the "wandering steering" and "excess play in the steering".
Read More...NHTSA ID Number: 11720654
Complaint Date: 2026-02-26
Fail Date: 2026-02-05
Manufacturer Name: Ford Motor Company
Vehicle Make: FORD
Vehicle Model: FUSION
Model Year: 2017
Summary
The contact owns a 2017 Ford Fusion. The contact stated that the vehicle was previously taken to a local dealer, and the transmission was replaced; however, while driving at an undisclosed speed, the vehicle was shaking abnormally while the accelerator pedal was depressed. No warning light was illuminated. The vehicle was taken to another local dealer, where it was diagnosed and it was determined that the engine needed to be replaced. The local dealer provided the contact with a rental vehicle. The vehicle was diagnosed with coolant intrusion in cylinders #2 and #4, DTC: P0316; and associated the failure with Customer Satisfaction Program: 19B37. The vehicle was not repaired due to the cost. The contact associated the failure with TSB 22-2322; however, the VIN was not included. The manufacturer was made aware of the failure. The failure mileage was approximately 119,322.
Read More...NHTSA ID Number: 11720653
Complaint Date: 2026-02-26
Fail Date: 2026-02-25
Manufacturer Name: Honda (American Honda Motor Co.)
Vehicle Make: HONDA
Vehicle Model: CIVIC
Model Year: 2016
Summary
The paint is flaking all areas surrounding the rear windshield which will cause rust damage and may lead to rear windshield needing to be replaced
Read More...NHTSA ID Number: 11720652
Complaint Date: 2026-02-26
Fail Date: 2025-10-11
Manufacturer Name: Honda (American Honda Motor Co.)
Vehicle Make: HONDA
Vehicle Model: CR-V
Model Year: 2018
Summary
I am filing this complaint regarding a serious safety issue with my 2018 Honda CR-V. The vehicle is experiencing repeated and unpredictable malfunctions involving the dashboard display, warning systems, and automatic braking features while the vehicle is in motion. While driving at normal speeds, the vehicle has braked on its own with no obstacle, vehicle, pedestrian, or hazard present in front of me. This sudden braking occurs without warning and creates a significant risk of being rear-ended or losing control of the vehicle. The braking feels as though the collision mitigation or safety system is activating incorrectly. At the same time or on separate occasions, the dashboard display begins glitching and flashing multiple warning indicators. These include: • Tire pressure warning lights appearing even though the tires are properly inflated • Sensor warning lights activating randomly • Alerts indicating systems such as collision warning, vehicle detection, or high-beam assist are malfunctioning • Messages stating safety features are not working when there is no apparent reason These warnings often appear simultaneously and disappear later without explanation. The infotainment or instrument display sometimes flickers or behaves erratically when this occurs. This issue is extremely concerning because it suggests a failure in the vehicle’s electrical system, sensors, or safety-assist technology. The unexpected braking alone poses a major safety hazard, particularly at highway speeds or in traffic, as it could cause a crash. In addition, the false warnings make it difficult to determine when the vehicle actually has a real problem that needs attention. The malfunction happens randomly and is not tied to weather conditions, road conditions, or driving behavior. It has occurred during normal driving with no obstacles present and no reason for the safety systems to activate. Because this issue involves unintended braking and malfunctioning driver
Read More...NHTSA ID Number: 11720651
Complaint Date: 2026-02-26
Fail Date: 2026-02-18
Manufacturer Name: General Motors, LLC
Vehicle Make: CHEVROLET
Vehicle Model: EQUINOX
Model Year: 2026
Summary
The contact rented a 2026 Chevrolet Equinox. The contact stated that while driving at approximately 35 MPH, a deer ran in front of the vehicle, and the vehicle crashed into the deer. During the crash, the vehicle sustained severe damage to the passenger-side front end, but no air bags deployed. During the incident, the contact sustained a lower abdomen injury, but no medical treatment was sought at this time. The dear sustained fatal injuries. A police report was taken at the scene. The cause of the failure was not determined. The manufacturer was not contacted regarding the incident. The vehicle was later returned to the rental company. The failure mileage was unknown.
Read More...NHTSA ID Number: 11720650
Complaint Date: 2026-02-26
Fail Date: 2026-02-26
Manufacturer Name: Toyota Motor Corporation
Vehicle Make: LEXUS
Vehicle Model: TX
Model Year: 2024
Summary
The vehicle's lower front fascia exhibits a design flaw, creating an unsafe gap that permits road debris to impact the condenser, leading to air conditioning system damage. This compromise in the A/C system's functionality results in an inability to adequately cool the vehicle's interior, thereby creating potentially unsafe operating conditions, particularly in high-temperature environments. It has been observed that dealerships are declining warranty coverage for these repairs, and the manufacturer has not provided any countermeasures to address this inherent design deficiency.
Read More...NHTSA ID Number: 11720649
Complaint Date: 2026-02-26
Fail Date: 2025-08-08
Manufacturer Name: Ford Motor Company
Vehicle Make: FORD
Vehicle Model: F-150
Model Year: 2024
Summary
The contact owns a 2024 Ford F-150. The contact received notification of NHTSA Campaign Number: 25V512000 (POWER TRAIN); however, the part to do the recall repair was not yet available. The local dealer was contacted. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure.
Read More...NHTSA ID Number: 11720648
Complaint Date: 2026-02-26
Fail Date: 2026-02-26
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: JEEP
Vehicle Model: WAGONEER
Model Year: 2024
Summary
The contact owns a 2024 Jeep Wagoneer. The contact stated while driving at an undisclosed speed, there was a loud whistling and vibrating sound coming from the door. The contact received notification of NHTSA Campaign Number: 25V593000 (Structure); however, the part to do the recall repair was not yet available. The vehicle was taken to the dealer, where it was determined that the door trim had failed and needed to be replaced. The vehicle was not repaired. The dealer confirmed that parts were not yet available. The manufacturer was not made aware of the failure. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The approximate failure mileage was 29,427.
Read More...
- CEL Doctor: The ANCEL AD310 is one of the best-selling OBD II scanners on the market and is recommended by Scotty Kilmer, a YouTuber and auto mechanic. It can easily determine the cause of the check engine light coming on. After repairing the vehicle's problems, it can quickly read and clear diagnostic trouble codes of emission system, read live data & hard memory data, view freeze frame, I/M monitor readiness and collect vehicle information.
- Sturdy and Compact: Equipped with a 2.5 foot cable made of very thick, flexible insulation. It is important to have a sturdy scanner as it can easily fall to the ground when working in a car. The AD310 OBD2 scanner is a well-constructed mechanic tool with a sleek design. It weighs 12 ounces and measures 8.9 x 6.9 x 1.4 inches. Thanks to its compact design and light weight, transporting the device is not a problem. The buttons are clearly labelled and the screen is large and displays results clearly.
- Accurate Fast and Easy to Use: The AD310 scanner can help you or your mechanic understand if your car is in good condition, provides exceptionally accurate and fast results, reads and clears engine trouble emission codes in seconds after you fixed the problem. This device will let you know immediately and fix the problem right away without any car knowledge. No need for batteries or a charger, get power directly from the OBDII Data Link Connector in your vehicle.
- OBDII Protocols and Car Compatibility: Many cheap scan tools do not really support all OBD2 protocols. AD310 scanner as it can support all OBDII protocols such as KWP2000, J1850 VPW, ISO9141, J1850 PWM and CAN. This device also has extensive vehicle compatibility with 1996 US-based, 2000 EU-based and Asian cars, light trucks, SUVs, as well as newer OBD2 and CAN vehicles both domestic and foreign. Pls confirm with our customer service whether it is compatible with your vehicle before purchasing.
- Home Necessity and Worthy to Own: This is an excellent code reader to travel or home with as it weighs less and it is compact in design. You can easily slide it in your backpack as you head to the garage, or put it on the dashboard, this will be a great fit for you. The AD310 is not only portable, but also accurate and fast in performance. Moreover, it covers various car brands and is suitable for people who just need a code reader to check their car.
- Multi-Functions - Practical Multi-Functions OBD2 code reader features built-in OBD2 DTC lookup library, which help you to determine the cause of the engine light, read code, erase code, view freeze frame, I/M ready, vehicle information, data flow, real-time curve, get vehicle speed information, calculate load value, engine coolant temperature, get engine speed.
- Wide Capability - Supports 9 protocols compatible with most 1996 US-Based, 2000 EU-Based and Asian cars, and newer OBD II & CAN domestic or import vehicles. Supports 6 languages - English,German, Dutch, Spanish, French, Italian.
- 2.8" LCD Display - Designed with a clear display 2.8" Large LCD screen - white backlight and contrast adjustment. No need any battery or charger, OBD reader gets the power directly from your vehicle through the OBDII Data Link Connector.
- Compact Design - Car diagnostic scanner is equipped with a 2.5 feet long cable and made of a very thick flexible insulator.There are 6 buttons on OBD2 Scanner:scroll up/down,enter/exit and buttons that quick query VIN vehicle number& the DTC fault code.
- ABS / Airbag codes NOT Supported - It is able to read and clear check engine information which is part of OBDII system, but it cannot work with non-OBDII systems, including ABS / Airbag / Oil Service Light, etc.
- 【Your Personal CEL Doctor – Read & Clear Engine Codes】The NT301 OBD2 scanner lets you read diagnostic trouble codes (DTCs), check em-issions readiness, turn off your Check Engine Light (CEL) or MIL, reset monitors, and view live data streams. It retrieves your vehicle's VIN instantly. Like all standard OBD2 scanners, it clears codes only after repairs are completed—if the issue persists, the code will return. Designed for DIYers who want to understand what’s really going on under the hood.
- 【Easy Code Reading – Just Plug & Play】Simply plug into the OBD2 port, turn the ignition to “ON” (engine off), and select the correct menu: Select OBDII-> Wait for seconds-> Select Read codes. For accurate results, ensure your vehicle is compatible and the OBD2 port is free from damage or wiring issues. No batteries needed— powered directly by your car.
- 【Live Data Graphing & Accuracy for Most OBD2 Vehicles】View and log live sensor data in graph form—monitor oxygen sensors, fuel trims, coolant temp, RPM, and more. Spot trends and suspicious values in real time. Compatible with most 1996+ gasoline cars, light trucks, and SUVs sold in the U.S., as well as many 2000+ European and Asian models. Also works on 12V diesel vehicles equipped with OBD2.
- 【S-mog Check Helper – Know Your Readiness Status at a Glance】With dedicated I/M readiness hotkeys and a simple Red-Yellow-Green LED indicator, you’ll instantly know if your vehicle is ready for em-issions testing. Built-in speaker provides audio feedback. No guesswork—just confidence before you head to the test center.
- 【A Must-Have Tool for Every Home Mechanic】Compact, rugged, and ready to use right out of the box. The 2.8” color screen is easy to read, even in daylight. No charging or setup required—just plug into the 16-pin DLC and start diagnosing. Recommended by professional mechanics on YouTube and trusted by DIYers worldwide.
Last update on 2026-03-20 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.