NHTSA ID Number: 11719107
Complaint Date: 2026-02-19
Fail Date: 2026-01-23
Manufacturer Name: General Motors, LLC
Vehicle Make: CHEVROLET
Vehicle Model: COLORADO
Model Year: 2023
Summary
Since Friday, February 23rd 2026 when my 2023 Chevy Colorado first start blowing oil out of the oil pan. almost 5 qts total was lost when it arrived at the dealership. Truck was out of service from Friday until the following Wednesday, January 28th. The truck was picked up and taken on a drive out to (January 29th, 2026) Waverly, KS from my hometown of Prairie Village, KS about 70 miles. On the way back home the truck went into safe mode at highway speeds. Lost all acceleration and barely made it off the side of the road before getting hit. Truck went back to dealership after being towed 70 miles. Where it was kept until Friday, February 6th. During this time at the dealership, they thought the problem was fixed, where again blew out all the oil while driving. Finally received the truck back. Check engine lights were still on but truck was holding oil and driving decent. Truck was doing fine until Monday February 16th. I was at a job and was driving home to finish the day. Again on the highway at highway speeds, truck goes into safe mode and limp it to gas station to again be empty on oil. It is still sitting there. Just last January the truck needed a new Transmission at 48,000 miles and at the same time a wirinig harness for the back-up camera needed replaced. Alot of things have been going wrong with this truck to be so new. It has cost me alot of out of pocket expenses.
Read More...NHTSA ID Number: 11719106
Complaint Date: 2026-02-19
Fail Date: 2026-02-03
Manufacturer Name: Toyota Motor Corporation
Vehicle Make: TOYOTA
Vehicle Model: PRIUS
Model Year: 2015
Summary
Inferior brake system on 2015 Prius master brake cylinder and vacuum booster. Extended warranty issues identified by Toyota for 10 years or 150, 000 miles. I bought my Prius used in 2021 with 92,000 miles at age [XXX] old intending it to last as long as I did. I am now [XXX] old and essentially totally independent. The above mentioned parts were identified as not functioning properly on 2/3/2026 (mileage 139, 106). On 2/6/26, I took it to Goettle Toyota, Ocala FL (mileage. 139,160) knowing there was an extended warranty program available that was admitting the parts were defective but not worthy of recall. I was advised the warranty for my vehicle expired 10/26/2025 (3 months and 8 days prior) and was now invalid. Brake replacement cost is $3675.00 + tax?. I was provided warranty information and instructed to call Toyota. I called, spoke with Brook and was advised the warranty was invalid due to date even though the car has less than the 150, 000 mile covered and nothing could be done. I was never notified of this issue so I could monitor for problems before the expiration. Average life for these items on a Prius is 250,000 miles, not 139, 000. I am on limited, fixed income and cannot afford this unnecessary repair. I am already gladly driving a 10 year old car to be independent. Loss of transportation changes my entire lifestyle. I cannot afford another car (if I could, I would be fixing this one). I would be reliant FOR THE REST OF MY LIFE, on others for all needs outside of my home. I live in a very rural area. I feel since I was NEVER notified of any issues and the car is LOW mileage and there should be another 100,000 miles on this car (I have driven it less than 50,000 miles in 5 years) that Toyota should honor the extended warranty based on the proximity of the malfunction to the ending of the warranty period and the LOW MILEAGE of the vehicle. This amount of money is NOTHING to Toyota but it is LIFE CHANGING to this, up until now, independent woma INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFOR
Read More...NHTSA ID Number: 11719105
Complaint Date: 2026-02-19
Fail Date: 2025-10-03
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: JEEP
Vehicle Model: WRANGLER
Model Year: 2014
Summary
My ABS module failed, which is a very well know issue with the 2014 to 2018 models. When the ABS module failed I was driving the vehicle and it went into fail safe mode while I was on the freeway service road. The speedometer stopped working and the vehicle would not go over about 20 mph. The vehicle was fine one minute and then I had no control of how fast I was going. I was with traffic that was going 60 mph and it could have been extremely dangerous for me or other drivers. The vehicle has been at the dealership since October 3rd, 2025 and has not been drivable due to this issue. It has not been inspected by anyone other than the dealership. There were warning lights but I was told that it was fine to drive until the part was available. It is currently on a national backorder for the last 18+ months without an estimated arrival date. The failure first appeared in June of 2024 and the part has been on backorder since then.
Read More...NHTSA ID Number: 11719104
Complaint Date: 2026-02-19
Fail Date: 2026-01-05
Manufacturer Name: General Motors, LLC
Vehicle Make: GMC
Vehicle Model: ACADIA
Model Year: 2024
Summary
In the process of taking my daughter to the emergency room I receive a dash notification on my recently purchased 2024 GMC Acadia "car overheating, possible engine failure". My gauges were within normal range and being that I was in an emergency I kept traveling. Leave hospital to head home the error message is gone. The following Monday, January 5th, heading in to work I receive the same error message on my dash "car overheating, possible engine failure". Drove to the nearest mechanic, left my car, and they discover a leak in the upper radiator hose. They call with bad news that the part is on nationwide back order. GM admitted to a faulty design, in the process of redesign. A SPAC case with a local GM dealership was opened. GM would expedite my case if I towed to a GM dealer. I would have to pay for the tow. And just how can my case be expedited if the part isn't available? It can't. I was told the redesigned hose is going on the new models currently being built. I have lost all faith in GM. Today is February 19th and my car is still at the mechanic with no ETA on part delivery. I called every GM dealership parts department within 100 miles and get the same response, "we have two hoses with four cars needing it, we have 4 hoses with 8 cars needing it, the hose is hell to find, etc.". Why has GM not issued a recall on the upper radiator hose. If you have a 2024 GMC Acadia, you will incur this same issue.
Read More...NHTSA ID Number: 11719103
Complaint Date: 2026-02-19
Fail Date: 2026-01-18
Manufacturer Name: Ford Motor Company
Vehicle Make: FORD
Vehicle Model: EXPLORER
Model Year: 2013
Summary
The contact owns a 2013 Ford Explorer. The contact received notification of NHTSA Campaign Number: 24V031000 (Structure); however, the part to do the recall repair was not yet available. The local dealer was made aware of the issue and confirmed that parts were not yet available. The contact stated that while driving rounding a corner at a slow speed, the front passenger’s side A-pillar trim detached and separated from the vehicle. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was not made aware of the issue. The vehicle was not repaired. The failure mileage was approximately 150,000.
Read More...NHTSA ID Number: 11719102
Complaint Date: 2026-02-19
Fail Date: 2026-02-14
Manufacturer Name: Jaguar Land Rover North America, LLC
Vehicle Make: LAND ROVER
Vehicle Model: DISCOVERY
Model Year: 2017
Summary
Water coming from top part of the front windshield. This was previously fixed but after few years problem persists and started causing electrical issues. I already had to replaced computer out of my pocket even it was under warranty cause did not wanted to fix it.
Read More...NHTSA ID Number: 11719101
Complaint Date: 2026-02-19
Fail Date: 2026-02-19
Manufacturer Name: Kia America, Inc.
Vehicle Make: KIA
Vehicle Model: EV6
Model Year: 2024
Summary
Vehicle Information: 2024 Kia EV6 (VIN: [XXX] ) Mileage at time of failure: 14,005 Complaint Description: My 2024 Kia EV6 experienced a complete failure of the 12-volt battery system despite the high-voltage traction battery showing approximately 80% state of charge. The vehicle became completely inoperable without warning. The 12-volt battery was fully discharged and the vehicle would not enter READY mode. The vehicle required a jump start to become operational. After being jump started, the 12-volt system did not appear to charge properly, suggesting a failure of the Integrated Charging Control Unit (ICCU), which is responsible for converting high-voltage battery power to maintain the 12-volt battery. This failure created a significant safety concern because: The vehicle became completely disabled without warning. This failure occurred while driving in heavy traffic, it created a hazardous situation. The vehicle’s electrical systems, including safety systems, depend on the 12-volt battery. There are known reports of ICCU failures in Kia and Hyundai electric vehicles that result in identical symptoms (sudden 12-volt battery discharge despite adequate traction battery charge). This suggests a potential systemic defect rather than normal battery wear. I am filing this complaint due to concern that this issue represents a broader safety defect affecting multiple vehicles and may require investigation or expanded recall action. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
Read More...NHTSA ID Number: 11719100
Complaint Date: 2026-02-19
Fail Date: 2024-08-19
Manufacturer Name: Ford Motor Company
Vehicle Make: FORD
Vehicle Model: F-150
Model Year: 2017
Summary
The contact owns a 2017 Ford F-150. The contact had previously received notification of Customer Satisfaction Program: 21N03 (Engine Cam Phaser Replacement), and the vehicle was taken to the dealer, where the contact was informed that no repair was needed. The contact stated that a year and a half later, the vehicle made an abnormal ticking sound while idling and while driving at various speeds. There was no warning light illuminated. The vehicle was taken to the dealer, where the starter was replaced; however, the failure recurred. The vehicle was taken back to the dealer, where it was diagnosed with cam phaser failure. The contact related the failure to the Customer Satisfaction Program: 21N03 (Engine Cam Phaser Replacement). The dealer replaced the cam phasers, the timing chain, the gaskets, the water pump, and other unknown parts. The vehicle was repaired at the owner's expense. The manufacturer was notified of the failure and informed the contact that the vehicle was no longer covered under the Customer Satisfaction Program. The failure mileage was approximately 65,208.
Read More...NHTSA ID Number: 11719099
Complaint Date: 2026-02-19
Fail Date: 2025-07-22
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: JEEP
Vehicle Model: GRAND WAGONEER
Model Year: 2024
Summary
Late last year I reported that while towing a trailer, the dash indicated that the trailer had disconnected from the trailer as looking back I noticed the lights were off when the vehicle lights were on. Before I could pull over to check the connection, the lights turned back on and the warning light extinguished. This happened 3 times when towing the trailer that day. The dealership "reprogrammed" the module and said it was good. But after the latest recall for the Wagoneer, having it recalled, I wanted to notify someone about the potential for expanding the vehicles included in the recall.
Read More...NHTSA ID Number: 11719098
Complaint Date: 2026-02-19
Fail Date: 2024-12-12
Manufacturer Name: Chrysler (FCA US, LLC)
Vehicle Make: RAM
Vehicle Model: 2500
Model Year: 2018
Summary
The contact owns a 2018 Ram 2500. The contact received notification of NHTSA Campaign Number: 24V896000 (Service Brakes, Hydraulic); however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The dealer was not made aware of the issue. The manufacturer was not made aware of the issue. The contact had not experienced a failure.
Read More...
- CEL Doctor: The ANCEL AD310 is one of the best-selling OBD II scanners on the market and is recommended by Scotty Kilmer, a YouTuber and auto mechanic. It can easily determine the cause of the check engine light coming on. After repairing the vehicle's problems, it can quickly read and clear diagnostic trouble codes of emission system, read live data & hard memory data, view freeze frame, I/M monitor readiness and collect vehicle information.
- Sturdy and Compact: Equipped with a 2.5 foot cable made of very thick, flexible insulation. It is important to have a sturdy scanner as it can easily fall to the ground when working in a car. The AD310 OBD2 scanner is a well-constructed mechanic tool with a sleek design. It weighs 12 ounces and measures 8.9 x 6.9 x 1.4 inches. Thanks to its compact design and light weight, transporting the device is not a problem. The buttons are clearly labelled and the screen is large and displays results clearly.
- Accurate Fast and Easy to Use: The AD310 scanner can help you or your mechanic understand if your car is in good condition, provides exceptionally accurate and fast results, reads and clears engine trouble emission codes in seconds after you fixed the problem. This device will let you know immediately and fix the problem right away without any car knowledge. No need for batteries or a charger, get power directly from the OBDII Data Link Connector in your vehicle.
- OBDII Protocols and Car Compatibility: Many cheap scan tools do not really support all OBD2 protocols. AD310 scanner as it can support all OBDII protocols such as KWP2000, J1850 VPW, ISO9141, J1850 PWM and CAN. This device also has extensive vehicle compatibility with 1996 US-based, 2000 EU-based and Asian cars, light trucks, SUVs, as well as newer OBD2 and CAN vehicles both domestic and foreign. Pls confirm with our customer service whether it is compatible with your vehicle before purchasing.
- Home Necessity and Worthy to Own: This is an excellent code reader to travel or home with as it weighs less and it is compact in design. You can easily slide it in your backpack as you head to the garage, or put it on the dashboard, this will be a great fit for you. The AD310 is not only portable, but also accurate and fast in performance. Moreover, it covers various car brands and is suitable for people who just need a code reader to check their car.
- Multi-Functions - Practical Multi-Functions OBD2 code reader features built-in OBD2 DTC lookup library, which help you to determine the cause of the engine light, read code, erase code, view freeze frame, I/M ready, vehicle information, data flow, real-time curve, get vehicle speed information, calculate load value, engine coolant temperature, get engine speed.
- Wide Capability - Supports 9 protocols compatible with most 1996 US-Based, 2000 EU-Based and Asian cars, and newer OBD II & CAN domestic or import vehicles. Supports 6 languages - English,German, Dutch, Spanish, French, Italian.
- 2.8" LCD Display - Designed with a clear display 2.8" Large LCD screen - white backlight and contrast adjustment. No need any battery or charger, OBD reader gets the power directly from your vehicle through the OBDII Data Link Connector.
- Compact Design - Car diagnostic scanner is equipped with a 2.5 feet long cable and made of a very thick flexible insulator.There are 6 buttons on OBD2 Scanner:scroll up/down,enter/exit and buttons that quick query VIN vehicle number& the DTC fault code.
- ABS / Airbag codes NOT Supported - It is able to read and clear check engine information which is part of OBDII system, but it cannot work with non-OBDII systems, including ABS / Airbag / Oil Service Light, etc.
- 【Your Personal CEL Doctor – Read & Clear Engine Codes】The NT301 OBD2 scanner lets you read diagnostic trouble codes (DTCs), check em-issions readiness, turn off your Check Engine Light (CEL) or MIL, reset monitors, and view live data streams. It retrieves your vehicle's VIN instantly. Like all standard OBD2 scanners, it clears codes only after repairs are completed—if the issue persists, the code will return. Designed for DIYers who want to understand what’s really going on under the hood.
- 【Easy Code Reading – Just Plug & Play】Simply plug into the OBD2 port, turn the ignition to “ON” (engine off), and select the correct menu: Select OBDII-> Wait for seconds-> Select Read codes. For accurate results, ensure your vehicle is compatible and the OBD2 port is free from damage or wiring issues. No batteries needed— powered directly by your car.
- 【Live Data Graphing & Accuracy for Most OBD2 Vehicles】View and log live sensor data in graph form—monitor oxygen sensors, fuel trims, coolant temp, RPM, and more. Spot trends and suspicious values in real time. Compatible with most 1996+ gasoline cars, light trucks, and SUVs sold in the U.S., as well as many 2000+ European and Asian models. Also works on 12V diesel vehicles equipped with OBD2.
- 【S-mog Check Helper – Know Your Readiness Status at a Glance】With dedicated I/M readiness hotkeys and a simple Red-Yellow-Green LED indicator, you’ll instantly know if your vehicle is ready for em-issions testing. Built-in speaker provides audio feedback. No guesswork—just confidence before you head to the test center.
- 【A Must-Have Tool for Every Home Mechanic】Compact, rugged, and ready to use right out of the box. The 2.8” color screen is easy to read, even in daylight. No charging or setup required—just plug into the 16-pin DLC and start diagnosing. Recommended by professional mechanics on YouTube and trusted by DIYers worldwide.
Last update on 2026-03-27 / Affiliate links / Images from Amazon Product Advertising API
This product presentation was made with AAWP plugin.